Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a simple process that can be achieved in just a few procedures.

• Begin by ensuring your red dot sight is powered on.
• Find the small reinitialize button on the rear of the device.
• Employ a paperclip to activate the reset switch for approximately 7 seconds.
• Disengage the reset button and your Holosun EPS Carry Red Dot sight will restart.
• The red dot sight should now be set back to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to default configuration is a breeze. First, locate the tiny button on the side of your optic. Then, keep pressed it for around ten seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Press and hold the power button for approximately 10 seconds.
• An indicator will flash, indicating that the reset is successfuly initiated.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and test your sight's functionality. If you encounter any further problems, don't hesitate to seek help from Holosun's support.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

• Initially, Turn on your Holosun EPS Carry by pressing the power button.
• Subsequently, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, activate the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reset your Holosun EPS Carry through a Factory Default Settings

If your Holosun EPS Carry is acting erratically, a factory reset might be the answer. This will return your sight to its here factory settings, clearing any altered configurations you've made. To accomplish this reset, observe these simple steps:

• First, find the reset switch on your EPS Carry.
• Secondly, engage a thin object, like a paperclip, to push the reset lever.
• As you hold the reset button pressed, power on your EPS Carry.
• It will blink a message confirming that the reset is complete.

Once the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page